Electric Circuit Analysis/Kirchhoff's Current Law

Wikiversity Electrical Engineering School
The Lessons in
ELECTRIC CIRCUITS ANALYSIS COURSE

Lesson Review 5:

What you need to remember from Kirchhoff's Voltage Law. If you ever feel lost, do not be shy to go back to the previous lesson & go through it again. You can learn by repitition.

Remember what was learned in Passive sign convention, You can go back and revise Lesson 1.

Define Kirchhoff's Voltage Law ( word-by-word ).

Kirchhoff's Voltage Law: $\sum _{n}v_{n}=v_{4}+v_{1}+v_{2}+v_{3}=0$

Lesson 6: Preview

This Lesson is about Kirchhoff's Current Law. The student/User is expected to understand the following at the end of the lesson.

Remember what was learned in Passive sign convention, You can go back and revise Lesson 1.

Define Kirchhoff's Current Law ( word-by-word ).

Kirchhoff's Current Law: $\sum _{n}i_{n}=i_{1}+i_{2}+i_{3}+i_{4}=0$

Lessons in Electric Circuit Analysis

Lesson #1:

Passive Sign Convention

Lesson #2:

Simple Resistive Circuits

Lesson #3:

Resistors in Series

Lesson #4:

Resistors in Parallel

Quiz Test:

Circuit Analysis Quiz 1

Lesson #5:

Kirchhoff's Voltage Law

Lesson #6:

Kirchhoff's Current Law

Lesson #7:

Nodal Analysis

Lesson #8:

Mesh Analysis

Quiz Test:

Circuit Analysis Quiz 2

Home Laboratory:

Circuit Analysis - Lab1

Part 1: Kirchhoff's Current Law

Kirchhoff's Current Law states:

The sum of the currents entering a particular point must be zero.

We can now define the electrical point physically connecting two or more electric circuit components, as a NODE. Note that a positive current leaving a point is considered to be a negative current entering that point.

Mathematically, Kirchhoff's Current Law is given by

 $\sum _{n}i_{n}=0$

For reference, this law is sometimes called Kirchhoff's first law, Kirchhoff's point rule, Kirchhoff's junction rule, and Kirchhoff's first rule.

Part 2:Kirchhoff's Current Law (Cont...)

Figure 6.1: $i_{1}+i_{2}+i_{3}+i_{4}=0$

We observe four currents "entering" the junction depicted as the bold black dot in Figure 6.1. Of course, two currents are actually exiting the junction , but for the purposes of circuit analysis it is generally less restrictive to consider what are in actuality positive currents flowing out of a junction to be negative currents flowing into that junction (mathematically the same thing). Doing so allows us to write Kirchhoff's law for this example as:

 $\sum _{n}i_{n}=i_{1}+i_{2}+i_{3}+i_{4}=0$

Part 3

It may not be clear at this point why we insist on thinking of negative currents flowing into a junction instead of positive currents flowing out. But note that Figure 6.1 provides us with more information that we generally can expect to get when analysing circuits, namely the helpful arrows indicating the direction of current flow. If we don't have such assistance, we generally should not pass judgment on the direction of current flow (i.e., placing a negative sign before our current variable) until we calculate it, lest we confuse ourselves and make mistakes.

Nevertheless in this case we have the extra information of directional arrows in Figure 6.1, so we should take advantage of it. We know that currents i₂ and i₃ flow into the junction and the currents i₁ and i₄ flow out. Thus we can write

i_{1}+i_{4}=i_{2}+i_{3}

Kirchhoff's Current Law as written is only applicable to steady-state current flow (i.e., no alternating current, no signal transmission). It can be extended to include time-dependent current flow, but that is beyond the scope of this section.

Kirchhoff's Current Law is used in a method of circuit analysis referred to as nodal analysis to be discussed in Lecture 7. A node is a section of a circuit where there is no change in voltage (where there are no components, wire is often assumed to be perfectly conductive).

Each node is used to form an equation, and the equations are then solved simultaneously, giving the voltages at each node.

Part 4 : Example

Figure 6.2: Example 1

Consider Figure 6.2 with the following Parameters:

V_{1}=15V

V_{2}=7V

R_{1}=20\Omega

R_{2}=5\Omega

R_{3}=10\Omega

Find current through $R_{3}$ using Kirchhoff's Current Law.

Solution:

Figure 6.3: Voltages at nodes

This is the same example we solved in Exercise 5.

Figure 6.3 shows Voltages at Nodes a, b, c and d.

We use node a as common node ( ground if you like ). thus $V_{a}=0V$ .

Part 5 : Example (Continued)

From Node b we get:

V_{b}=-V_{1}=-15V

From Node d we get:

V_{d}=V_{2}=7V

It is clear that we must solve Vc, in order to complete Voltage definitions at all nodes. Vc will be found by applying KCL at node c and solving the resulting equations as follows:

$i_{1}=i_{2}+i_{3}$

${\frac {V_{b}-V_{c}}{R_{1}}}={\frac {V_{c}}{R_{3}}}+{\frac {V_{c}-V_{d}}{R_{2}}}$

and

${\frac {V_{b}}{R_{1}}}-{\frac {V_{c}}{R_{1}}}-{\frac {V_{c}}{R_{3}}}-{\frac {V_{c}}{R_{2}}}+{\frac {V_{d}}{R_{2}}}=0$

We can group the like terms to get the following equation:

 $V_{c}\left({\frac {1}{R_{1}}}+{\frac {1}{R_{2}}}+{\frac {1}{R_{3}}}\right)={\frac {V_{b}}{R_{1}}}+{\frac {V_{d}}{R_{2}}}$

Part 6 : Example (Continued)

Substitute values into previous equations you get:

 $V_{c}\left({\frac {1}{20\Omega }}+{\frac {1}{5\Omega }}+{\frac {1}{10\Omega }}\right)={\frac {-15V}{20\Omega }}+{\frac {7V}{5\Omega }}$

 $V_{c}(0.35)=0.65$    thus    $V_{c}=1.857V$

Thus now we can calculate Current through $R_{3}$ as follows:
${\begin{matrix}\ I_{R3}&=&{\frac {V_{c}}{R_{3}}}\\\ \\\ &=&{\frac {1.857}{10}}\\\ \\\ &=&0.186A\end{matrix}}$ .